1994 Saab 900

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE INSTRUCTIONS FOR PROPERLY AIMING THE HEADLIGHTING SYSTEM WERE OMITTED. THIS DOES NOT MEET THE REQUIREMENTS OF FMVSS NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

RiskIF THE HEADLAMP ASSEMBLIES ARE REPLACED, CUSTOMERS MAY NOT BE ABLE TO PROPERLY AIM THE HEADLIGHTS.

FixOWNERS WILL BE SENT AIMING INSTRUCTIONS, AND DIRECTIONS FOR AFFIXING THESE INSERTS TO THE OWNER GUIDES. IF AN OWNER SO DESIRES, A DEALER CAN AFFIX THE INSERTS IN THEIR OWNER GUIDE FOR THEM.

CORROSION AROUND THE ZINC-COATED THROTTLE CONTROL LEVER BUSHING CAN CAUSE THE THROTTLE LEVER TO BIND.

RiskTHIS BINDING CAN RESULT IN THE THROTTLE PLATE NOT RETURNING TO THE CLOSED POSITION WHEN THE THROTTLE PEDAL IS RELEASED AND A SUBSEQUENT LOSS OF THROTTLE CONTROL.

FixDEALERS WILL REPLACE THE ZINC-COATED THROTTLE CONTROL LEVER BUSHING WITH A NICKEL-COATED BUSHING AND BOLT.

IT IS POSSIBLE TO MOVE THE SHIFT LEVER INTO THE REVERSE GEAR POSITION, REMOVE THE IGNITION KEY, AND STILL HAVE THE TRANSMISSION IN NEUTRAL, OR, TO ACCIDENTLY DISENGAGE REVERSE BY STRIKING THE GEAR LEVER.

RiskIF THE PARKING BRAKE IS NOT APPLIED, THE CAR CAN ROLL FROM ITS ORIGINAL PARKED POSITION INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.

FixDEALERS WILL REPLACE TRANSMISSION LINKAGE COMPONENTS AND COMPLETE A SPECIALLY DEVELOPED SERVICE ADJUSTMENT PROCEDURE THAT WILL ENSURE THAT WHEN THE SHIFT IS MOVED TO THE REVERSE POSITION, THE REVERSE GEAR IS ACTUALLY ENGAGED.

ONE OR MORE OF THE ARC WELDS CAN BE MISSING ON THE SEAT BACK FRAME RECLINER.

RiskTHIS CAN RESULT IN A SEAT BACK FALLING BACKWARDS UNDER A LOAD.

FixBOTH FRONT SEAT BACKS WILL BE INSPECTED WITH THE USE OF A HOOK TO PULL BACK THE SEAT BACK UPHOLSTERY. FOR ANY SEAT WITH MISSING WELDS, THE SEAT BACK FRAME/RECLINER WILL BE REPLACED.

THE TWO WELD POINTS IN THE REARWARD ATTACHMENT BRACKET FOR THE SIDE IMPACT PROTECTION BEAM IN THE REAR DOOR MAY BE OUT OF POSITION. IF THE WELDS ARE OUT OF POSITION, THE VEHICLES WILL NOT MEET THE REQUIREMENTS OF FMVSS 214, S5, "SIDE DOOR STRENGTH."

RiskCONSEQUENCE OF NON-COMPLIANCE: PASSENGERS SITTING IN THE REAR SEATS WILL BE SUBJECT TO AN INCREASED RISK OF INJURY IN THE EVENT OF A SIDE COLLISION.

FixDEALERS WILL INSTALL SUPPORT BRACKETS AT THE SUPPORT WELD LOCATIONS.

TWO TRIGGER SPRINGS MOUNTED TO THE FORE/AFT ADJUSTMENT LEVER DO NOT DEVELOP SUFFICIENT FORCE TO PROPERLY LOCK THE SEAT RAILS. AFTER THE SEAT IS ADJUSTED, THIS DOES NOT ALLOW THE SEAT RAIL LOCK TO PROPERLY ENGAGE, WHICH CAN CAUSE THE SEAT TO MOVE IN A SUDDEN STOP OR COLLISION.

RiskTHIS CAN INCREASE THE POSSIBILITY OF INJURY TO A SEAT OCCUPANT IN THE EVENT OF A SUDDEN STOP OR ACCIDENT.

FixDEALERS WILL REMOVE BOTH FRONT SEATS AND THE TWO SPRINGS ON EACH SEAT WILL BE REPLACED WITH NEW SPRINGS WITH PROPER TENSION TO ENSURE PROPER ENGAGEMENT.

A WELD IN THE SEAT RAILS WAS NOT MADE, INCREASING THE RISK OF FATIGUE CRACKS FORMING AROUND THE ATTACHMENT BUSHINGS ON THE HEIGHT ADJUSTMENT MECHANISM, CAUSING THE POSSIBILITY OF THE HEIGHT ADJUSTER BREAKING IN A REAR END COLLISION AND ALLOWING THE SEAT TO FOLD BACKWARDS.

RiskTHIS CAN INCREASE THE RISK OF INJURY TO SEAT OCCUPANTS.

FixDEALERS WILL INSTALL NEW FRONT SEAT FRAME RAILS.

THE ORIGINAL FRONT BRAKE DISCS AND/OR PADS SHIELDS DO NOT PROTECT THE ASSEMBLIES FROM BEING COATED WITH A LAYER OF SLUSH, ROAD SALT OR WATER WHILE DRIVING IN SNOW OR HEAVY RAIN. THIS CAN RESULT IN A DELAY IN BRAKING ACTION THAT INCREASES NORMAL STOPPING DISTANCE.

RiskINCREASED STOPPING DISTANCE COULD RESULT IN AN ACCIDENT.

FixDEALERS WILL REPLACE THE ORIGINAL FRONT BRAKE SHIELDS WITH A NEW DESIGN. AN ADDITIONAL HOLE WILL BE DRILLED IN THE STEERING KING PIN HOUSING TO ATTACH A LARGER COVER PLATE. A SMALLER PROTECTION PLATE WILL ALSO BE ATTACHED TO THE EXISTING TWO BOLTS IN THE HUB.

DEFECTIVE WATER PUMP PULLEY

NEW WHEEL BOLTS

AUDIO SYSTEM FIRES