Year · Make · Model
What the National Highway Traffic Safety Administration knows about this vehicle: every recall, every consumer complaint, every defect investigation, every NCAP crash test. Sourced directly from NHTSA data feeds.
THE PITMAN ARM RETAINING NUT MAY NOT HAVE BEEN TORQUED TO MANUFACTURER SPECIFICATIONS. THIS COULD RESULT IN INADEQUATE RETENTION OF THE NUT AT THE OUTPUT SHAFT, ALLOWING THE PITMAN ARM TO BECOME LOOSE.
FixDEALER WILL INSPECT AND RETORQUE PITMAN ARM, IF NECESSARY, AT NO COST TO OWNER.
IN THE EVENT OF TURBOCHARGER COMPRESSOR WHEEL FAILURE, ONE OR MORE OF THE FOUR CAPSCREWS THAT HOLD THE TURBOCHARGER TOGETHER MAY BE STRUCK BY PARTS OF THE COMPRESSOR WHEEL, RESULTING IN THE CAPSCREWS BEING DAMAGED. IF THESE CAPSCREWS ARE DAMAGED TO THE POINT THAT THEY ALLOW THE COMPRESSOR BACK PLATE TO DISLOCATE FROM THE TURBOCHARGER BEARING HOUSING, ENGINE LUBRICATING OIL MAY BE ALLOWED TO ESCAPE UNDER PRESSURE, CONTACTING THE ENGINE EXHAUST MANIFOLD SECTIONS OR TURBOCHARGER TURBINE HOUSING.
FixDEALER WILL INSTALL A SHIELD FOR THE HEADS OF THE FOUR CAPSCREWS, ALONG WITH STRONGER SAE 8 GRADE 8 CAPSCREWS, IF NECESSARY, AT NO COST TO OWNER.
DELAYS OF UP TO ABOUT 2 SECONDS MAY EXIST IN THE BRAKE APPLICATION TIMES TO THE BRAKES ON THE BOGIE AXLES IN THE PRESENCE OF CERTAIN TYPES OF WHEEL SPEED SENSOR SIGNAL DISCONTINUITIES OR DISTORTIONS THAT MAY OCCUR AS A RESULT OF SENSOR WIRE FAILURE. THIS CONSTITUTES A NON-COMPLIANCE TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS".
FixDEALER WILL INSTALL NEW WHEEL SPEED SENSORS THAT INCORPORATE IMPROVED WIRING AND THE PRESENT BOGIE ANTI-WHEEL LOCK SYSTEM WILL BE CHANGED TO AN AXLE-TO-AXLE SYSTEM FOR IMPROVED RELIABILITY.
THE POSSIBILITY EXISTS THAT THE ALUMINUM ENGINE REAR SUPPORT BRACKETS MAY FAIL DUE TO METAL FATIGUE. THIS TYPE OF FAILURE WOULD ALLOW THE ENGINE AND TRANSMISSION ASSEMBLY TO DISLOCATE DOWNWARD. THIS WILL RESULT IN THROTTLE CONTROL LOSS WITH THE ENGINE OPERATING CONTINUOUSLY IN THE MID TO UPPER RANGE OF THE GOVERNED SPEED RANGE.
FixDEALER WILL INSPECT AND, IF NECESSARY, REPLACE ALUMINUM SUPPORT BRACKETS WITH BRACKETS MADE FROM DUCTILE IRON FOR INCREASED STRENGTH.
A DESIGN DEFICIENCY EXISTS IN THE AIR DRYER PIPING IN THE AREA OF THE PRESSURE RELIEF VALVE AND COMPRESSOR GOVERNOR CONTROL LINK. MOISTURE IS PASSED AND BUILDS UP IN THIS RELIEF VALVE AND CONTROL LINE. IN FREEZING AMBIENT TEMPERATURES, THIS MOISTURE MAY FREEZE, ALLOWING THE CHASSIS AIR SYSTEM PRESSURE TO EXCEED 150 PSI. EXCESSIVE AIR SYSTEM PRESSURE CAN CAUSE SEPARATION OF AIR PIPING CONNECTIONS AND AIR SYSTEM VALVE FAILURE.
FixTHE DEALER WILL RELOCATE THE AIR SYSTEM COMPRESSOR GOVERNOR LINE AND PRESSURE RELIEF VALVE TO ELIMINATE MOISTURE ACCUMULATION.
A DEFICIENCY EXISTS IN THE WELDS SECURING THE REAR SPRING INSULATOR BRACKET TO THE AXLE HOUSING. THIS IS DUE TO IMPROPER POSITIONING OF THE WELD, IN RELATIONSHIP TO THE BRACKET AND AXLE HOUSING. FAILURE OF THE WELDS WOULD CAUSE SEPARATION OF THE SPRING INSULATOR BRACKET AND THE AXLE HOUSING, RESULTING IN IMPROPER ALIGNMENT OF THE AFFECTED AXLE.
FixDEALER WILL REWELD THE INSULATOR SPRING BRACKET AT NO COST TO OWNER.
THE FLEX BLADE FANS ON THE INVOLVED VEHICLES MAY DEVELOP CRACKS IN THE LAMINATED STIFFENER AS A RESULT OF FATIGUE DURING OPERATION. IF SUCH A CONDITION EXISTS AND THE CRACKS GO UNDETECTED, CONTINUED OPERATION COULD CAUSE PIECES OF THE STIFFENER TO BREAK OFF.
FixDEALER WILL REPLACE THE ORIGINAL FAN WITH A STEEL FIXED BLADE FAN, FREE OF CHARGE.
THE FRONT WHEEL ALUMINUM HUBS ON THE INVOLVED VEHICLES MAY BE SUBJECT TO CRACKS WHICH MAY PROGRESS CIRCUMFERENTIALLY AROUND THE BARREL OF THE HUB. THIS COULD LEAD TO A FRACTURE IN THE "BARREL" POSITION OF THE HUB AND COMPLETE HUB FAILURE.
FixDEALER WILL INSTALL STEEL HUBS IN PLACE OF ALUMINUM HUBS WITHOUT CHARGE TO OWNER.