1995 Ford F700

VEHICLE DESCRIPTION: MEDIUM DUTY TRUCKS EQUIPPED WITH 7.0L LIQUEFIED PETROLEUM GAS (LPG) ENGINE OR 7.0L EFI (GASOLINE) ENGINE WITH THE OPTIONAL CAB FLOOR PAN REINFORCEMENT. THE ENGINE WIRING HARNESS OR BATTERY CABLE CAN BE PINCHED BETWEEN THE OPTIONAL CAB REINFORCEMENT AND THE FRAME CAUSING AN ABRASION WHICH COULD RESULT IN AN ELECTRICAL SHORT CIRCUIT.

RiskA SHORT CIRCUIT CAN CAUSE OVERHEATING AND ARCING.

FixDEALERS WILL MODIFY THE REINFORCEMENT(S) AND, IF NECESSARY, REPOSITION THE ENGINE WIRING HARNESS (INCLUDING INSTALLATION OF THE REVISED ENGINE WIRE HARNESS RETENTION BRACKET) AND BATTERY CABLE.

VEHICLE DESCRIPTION: MEDIUM DUTY TRUCKS EQUIPPED WITH 7.0L LIQUEFIED PETROLEUM GAS (LPG) ENGINE OR 7.0L EFI (GASOLINE) ENGINE WITH THE OPTIONAL CAB FLOOR PAN REINFORCEMENT. THE ENGINE WIRING HARNESS OR BATTERY CABLE CAN BE PINCHED BETWEEN THE OPTIONAL CAB REINFORCEMENT AND THE FRAME CAUSING AN ABRASION WHICH COULD RESULT IN AN ELECTRICAL SHORT CIRCUIT.

RiskA SHORT CIRCUIT CAN CAUSE OVERHEATING AND ARCING.

FixDEALERS WILL MODIFY THE REINFORCEMENT(S) AND, IF NECESSARY, REPOSITION THE ENGINE WIRING HARNESS (INCLUDING INSTALLATION OF THE REVISED ENGINE WIRE HARNESS RETENTION BRACKET) AND BATTERY CABLE.

THE HAND THROTTLE CABLE CAN WEAR THE BRASS SWIVEL BLOCK ON THE GOVERNOR LEVER THROUGH WHICH IT PASSES.

RiskTHIS WEAR CAN RESULT IN THE GOVERNOR JAMMING IN THEDAMAGED SWIVEL AND COULD PREVENT THE GOVERNOR LEVER FROM RETURNING TO THE IDLE POSITION.

FixDEALERS WILL INSTALL A REVISED GOVERNOR LEVER WITH A STAINLESS STEEL SWIVEL. ALSO LETTERS WILL BE SENT TO VEHICLE OWNERS THAT HAVE THE SAME VEHICLES BUT DO NOT HAVE A FORD INSTALLED HAND THROTTLE ADVISING THEM THAT THEY MAY REQUIRE SERVICE IF THEY HAVE HAD AN AFTER MARKET HAND THROTTLE INSTALLED.

AIR SYSTEM BLOCKAGE IN THE AIR DRYER OCCURS DEGRADING THE MOISTURE REMOVING CAPABILITIES OF THE DRYER WHEN THE VEHICLE IS OPERATED IN A COLD ENVIRONMENT AND MOISTURE ACCUMULATES AND FREEZES IN THE AIR DRYER OR IN THE LINE BETWEEN THE DRYER AND THE AIR SYSTEM RESERVOIR. THE AIR DRYER CAN BECOME OVERPRESSURIZED CAUSING THE AIR DRYER CARTRIDGE TO SEPARATE FROM THE MOUNTING BASE.

RiskIF THE AIR DRYER SEPARATES FROM THE BASE, THE CARTRIDGE CAN SEPARATE SUFFICIENTLY ENOUGH TO CAUSE PERSONAL INJURY OR PROPERTY DAMAGE.

FixDEALERS WILL EQUIP AIR SYSTEMS WITH A PRESSURE RELIEF VALVE TO BE LOCATED BETWEEN THE COMPRESSOR AND THE AIR DRYER. THIS PRESSURE RELIEF VALVE IS INTENDED TO VENT IF EXCESSIVE PRESSURE DEVELOPS IN THE AIR DRYER.

A CONNECTOR IN THE WIRING WHERE THE TILT HOOD MOUNTED LAMPS ATTACH TO THE VEHICLE WIRING HARNESS WAS BUILT WITHOUT SEALING PLUGS. MOISTURE, ROAD SALT OR OTHER CONTAMINANTS CAN ENTER THE CONNECTION RESULTING IN CROSSED CIRCUITS, SHORTS OR CORROSION OF THE WIRING OF THE CONNECTOR.

RiskTHE HEADLAMPS OR OTHER FRONT-END LIGHTING SYSTEMS CAN MALFUNCTION AS A RESULT OF THIS CONDITION INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.

FixDEALERS WILL INSPECT THE CONNECTOR AND INSTALL SEALING PLUGS IN THE OPEN CAVITIES. IF THE INSPECTION REVEALS CORROSION, A NEW CONNECTOR WILL BE INSTALLED.

THE DRAG LINK INSTALLED CAN CONTACT THE FRONT AXLE I-BEAM UNDER CERTAIN EXTREME CONDITIONS. THIS DRAG LINK WAS NOT INTENDED TO BE INSTALLED ON "LOW PROFILE" VEHICLES.

RiskTHIS CAN RESULT IN LOSS OF STEERING CONTROL.

FixDEALERS WILL INSTALL THE CORRECT DRAG LINK ON THE VEHICLES.