1979 Ford F250

CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.

RiskA LEAKING FUEL PUMP COULD CREATE A VEHICLE FIRE HAZARD.

FixFEDERAL-MOGUL WILL NOTIFY OWNERS AND REPLACE THE DEFECTIVE FUEL PUMPS FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 15, 2007. OWNERS CAN CONTACT FEDERAL-MOGUL AT 248-354-7700.

DIMENSIONAL DIFFERENCES IN THE 1980 VERSUS THE 1979 ASSEMBLIES MAY ALLOW THE INNER BRAKE LINING/SHOE TO MOVE OUTWARD TO A POSITION WHERE IT IS NO LONGER RETAINED IN THE SHOE SLOT WHEN THE FRONT BRAKE INNER LININGS BECOME WORN TO THE POINT OF NEEDING REPLACEMENT. THE INNER BRAKE SHOE COULD THEN WEDGE BETWEEN THE ROTOR AND SPINDLE, POSSIBLY CAUSING A SUDDEN LOCK-UP OF ONE FRONT WHEEL. THIS CAN OCCUR WITHOUT BRAKE APPLICATION AND WOULD ADVERSELY AFFECT STEERING CONTROL. THESE DIMENSIONAL DIFFERENCES COULD ALSO ALLOW ADDITIONAL TRAVEL OF THE BRAKE PISTON SUCH THAT A LOSS OF BRAKE FLUID FROM THE FRONT BRAKE SYSTEM MAY OCCUR. THIS WOULD RESULT IN INCREASED STOPPING DISTANCES.

FixTHE DEALER WILL INSPECT AND, IF NECESSARY, REPLACE THE HUB AND ROTOR ASSEMBLIES AND SPINDLE SEALS.

THE INVOLVED VEHICLES WERE PRODUCED WITH BRAKE PUSH-ROD TO BRAKE PEDAL RETAINING PINS WHICH WERE NOT HEAT-TREATED AS SPECIFIED. THIS COULD ALLOW THE BRAKE PEDAL TO BECOME DISENGAGED FROM THE PUSH-ROD.

FixDEALER WILL REPLACE THE SUSPECT BRAKE RETAINING PIN.

THE INVOLVED VEHICLES WERE ASSEMBLED WITH IMPROPERLY MANUFACTURED STEERING ARM KNUCKLES. SHOULD AN IMPROPERLY MANUFACTURED STEERING ARM KNUCKLE FRACTURE AND SEPARATE, THE STEERING LINKAGE TIE ROD MAY DISENGAGE FROM THE KNUCKLE.

FixTHE DEALER WILL INSPECT FOR CRACKING IN THE STEERING ARM KNUCKLES ON ALL VEHICLES AND, IF NECESSARY, REPLACE THEM FREE OF CHARGE.

THE INVOLVED VEHICLES WERE MANUFACTURED WITHOUT A FUEL TANK SHIELD AT THE FRONT RIGHT CORNER OF THE MIDSHIP FUEL TANK. AS A RESULT, THE VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 301, "FUEL SYSTEM INTEGRITY". IN THE EVENT OF A VEHICLE ACCIDENT, EXCESSIVE FUEL SPILLAGE COULD RESULT.

FixTHE DEALER WILL INSTALL THE REQUIRED FUEL TANK SHIELD WITHOUT CHARGE TO OWNER.

THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 212, "WINDSHIELD MOUNTING", IN THAT SOME OF THE VEHICLES WERE BUILT WITHOUT THE SPECIFIED WINDSHIELD WEATHERSTRIP RETAINING COMPONENTS.

FixTHE DEALER WILL INSTALL THE WINDSHIELD WEATHERSTRIP RETAINING COMPONENTS AT NO COST TO OWNER.

THE INVOLVED VEHICLES WERE EQUIPPED WITH AUTOMATIC TRANSMISSIONS IN WHICH THE PARKING PAWL WAS NOT HEAT-TREATED. DURING NORMAL VEHICLE OPERATION, A PARKING PAWL THAT HAS NOT BEEN HEAT-TREATED COULD BECOME DEFORMED OR WORN TO THE POINT THAT THE TRANSMISSION WILL NOT LOCK IN "PARK". AS A RESULT, THE VEHICLE COULD ROLL FREE IF THE DRIVER DOES NOT SET THE PARKING BRAKE WHEN PARKING OR LEAVING VEHICLE UNATTENDED.

FixDEALER WILL INSPECT AND, IF NECESSARY, REPLACE THE PARKING PAWL WITH ONE THAT HAS BEEN HEAT-TREATED.

THESE TRANSMISSIONS MAY CONTAIN IMPROPERLY MANUFACTURED PARKING PAWL ACTUATING RODS. CONSEQUENTLY, THE UNHARDENED CAM SURFACE OF THESE RODS CAN ALLOW THE ROD TO DEFORM DURING USE WITH RESULTANT INCREASE IN SHIFT EFFORTS AND DIFFICULTY IN RELEASING THE PARKING PAWL AND ENGAGING THE PARKING GEAR.

FixDEALER WILL REPLACE THE TRANSMISSION PARKING PAWL ACTUATING ROD WITHOUT CHARGE TO OWNER.